Pool Covers
Showing 1–24 of 41 results
-
Pool Covers, Pool Products
AUTOMATIC COVERINGS
DESCRIPTIONS
in this system, the spindle is immersed in the pool and is supported with two flanges, which are bolted to the pool shell. The motor that winds and unwinds the cover is located inside the spindle (inroller motor Logic) and its cable passes through the pool shell in a sleeve. The cover is operated automatically by using a key switch and the limits are programmed electronically.COMPONENTS
The following elements are included in the drive system:
• Stainless steel spindle made to measure
• Stainless steel flanges, 30 mm shaft & locking ring
• Stainless steel sleeve through wall with flexible reinforced hose & hose clamp
• Logic motor 24 V DC
• Logic 250 – IP68 – 250 Nm – 4 rpm
• Logic 500 – IP68 – 500 Nm – 4 rpm
• Control panel IP56, including touch pad, safety transformer 230V AC/24V AC – 300 VA, circuit board 24V DC 20A
• Flush or surface key switch IP54 with open, close, stop functions
• Set of straps
• Set of directional guides
• Screws, bolts & other fixings includedSKU: HS9671 -
Cover and Roller Accessories
Automatic covers: Accessories
We offer a line of accessories for both the use and the maintenance of the automatic cover.
In compliance with the French standard NF P90-308 for swimming pool covers the following straps will be supplied according to the kind of cover and swimming pool:
Submerged models and above-ground models with protective casing:
Cover with steps: 3 units
Cover without steps: 2 units
Above-ground models:
Cover with steps: 5 units (2 next to the motor and 3 next to the steps)
Cover without steps: 4 units (2 next to the motor and 2 on the opposite side)SKU: HS7886 -
Automatic Covers and Reel Systems
Carlit solar model
The automatic solar pool cover Carlit runs on solar energy, making it a very environmentally-friendly product. It reduces water evaporation and heat loss in your pool. The cover also minimises premature evaporation of pool chemicals. Certified by the French standard NF 90-308, the Carlit solar pool cover guarantees higher quality, reducing possible accidents arising from children, animals, or objects falling into the water.
Precautions for installation: THE SUN MUST DIRECTLY COME INTO CONTACT WITH THE PHOTOVOLTAIC PLATE. DO NO INSTALL U NDER A TREE OR FACING NORTH.
SKU: HS2394 -
Automatic Covers and Reel Systems
Commercial roller AERIAL type
These motorized pool rollers are for pools with dimensions of up to 25 x 16 m (according to the model). It is a product that works outside the pool. They can cover pools with bubble or armed polyethylene foam covers. The option for PVC slats is not available.
AERIAL type
This roller is installed on the edge of the pool at a height of up to 3m from the ground, for the purpose of not closing off access to the pool from the roller side. Requires electrical wiring. The maximum length of the axle makes it possible to cover a pool width of 12.5 m and up to 25 metres long.SKU: HS8353 -
Automatic Covers and Reel Systems
Commercial roller BORNA type
This shaft is aimed to install on commercial indoor or outdoor swimming pools of 12.5 x 25 meters maximum. It can be used for bubble or reinforced polyethylene foam covers.The distance between the roller shaft and the pool edges must be reduced as much as possible to prevent abnormal wear and tear due to the friction on the coping.
SKU: HS6489 -
Automatic Covers and Reel Systems
Commercial roller DOUBLE AXLE type
These motorized pool rollers are for pools with dimensions of up to 25 x 16 m (according to the model). It is a product that works outside the pool. They can cover pools with bubble or armed polyethylene foam covers. The option for PVC slats is not available.
DOUBLE AXLE type
This mobile roller has two axes for two identical covers measuring 8 metres wide each. The structure is supported on 6 wheels which enable movement of the roller.SKU: HS4252 -
Automatic Covers and Reel Systems
Motor in dry mortar
The Roussillon automatic cover is the submerged model which incorporates the motor in a separate sunken compartment, and both the roller axle as well as the cover are housed at one end inside the pool itself.
The submerged zone containing the roller axle should be separated by a small concrete partition at the time of construction or with a PVC partition later on.
The basic elements for assembling the cover are the slats, the step slats, (from page 439), the mechanical kit, the embedding kit, the aluminium tie beam and the pit cover.
MECHANICAL KIT
Includes the following elements:
– Ø 146 mm extruded aluminium axle, 5 mm thick and Ø 30 mm joint shaft.
– Motor stand.
– Watertightness joints on bushing side.
– Watertightness joints on bearing stand side.
– 24 V reducer motor with stainless steel stand.
– 220/24V standard switchboard.
– On-off key switch.
Should be installed in full view of the pool. It works by continuous turning of the key.SKU: HS2567 -
Automatic Covers and Reel Systems
Motor on the shaft
The motor is integrated into the interior of the roller axle and can be installed in already existing pools of up to 6 metres in width.
As in the Roussillon model the submerged zone containing the roller axle should be separated by a small concrete partition at the time of construction or later with a PVC partition. The slat colours available for both models are white, beige and opaque blue.SKU: HS7976